Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
What are your opinions on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently accessible, the job can relocate easily; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and also embeded in the brand-new one. See to it you have qualified yourself for the work as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you may require an expert plumber to make tube links.
This short article will assist you set up a brand-new bath tub in your restroom if you have already acquired a new tub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wooden boards are valuable in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its last placement.
Planning for the Installation
Firstly, the supporting framework provided with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the tiles utilizing waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that article on Tools You Need to Install a New Bathtub while perusing the web. Sharing is good. Helping others is fun. Thanks so much for taking the time to read it.
Book Today! Report this page